The White wire is common for the fan and light kit. Note: The Black wire is hot power for the fan. Connect the White (neutral) supply wire to the White fan wire.Connect the Black (hot) supply wire to the Black fan wire.Connect the Bare/Green (ground) supply to Green wires from the fan and the mounting bracket.Secure all wiring connections with wire connectors (AA) according to the diagram and these steps:
If your house wire is larger than 12-gauge and there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use.ĬAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.ġ. WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. Note: The downrod (A) should not rotate if installed correctly Align one of the four slots in the ball with the tab in the mounting bracket (D).
Harborbreeze fans install#
Install the ball end of the downrod (A) into the opening of mounting bracket (D). Note: If you did not cut back the lead wires in Step 4, Step 5 is not necessary and you may proceed to Step 6.Ħ. Repeat this step for black and green wires. Twist the stripped ends of each strand of wire within the insulation with pliers (not included). of insulation from the end of the white wire. If you decided to cut back the lead wire in Step 4, strip 1/2 in. Measure at least 8 inches of lead wire, then cut the excess wire off with wire cutters (not included).ĥ. If you decide to cut back the lead wires, take the lead wires and make sure you have pulled them all the way through the top of the downrod. Depending on the length of downrod you use, you may need to cut the lead wires back to simplify the wiring. Slide the downrod (A) into the yoke of the motor assembly (G), align the holes, then re-install the downrod clip (C) and downrod pin (B). Feed the wires from the motor assembly (G) through the downrod (A).ģ. Insert the downrod (A) through the canopy (E) and yoke cover (O). Then, partially loosen the set screws (Q) in the yoke at the top of the motor assembly (G).Ģ. Remove the downrod pin (B) and downrod clip (C) from the downrod (A). Discard the orange packing material from the top and bottom of the motor assembly (G) but save the three fitter plate screws (I) for later.ġ. Remove the three fitter plate screws (I) and the packing material from the motor assembly (G). Important: If using the angle mount, ensure the open end of the mounting bracket (D) is installed facing the floor.Ħ. Attach mounting bracket (D) to outlet box (not included) using screws and washers provided with the outlet box.ĬAUTION: It is very important to use the proper hardware when installing the mounting bracket (D) as this will support the fan. Note: If using this item on an angled ceiling, snap out the perforated section of the canopy cover (F).ĥ. Set aside for later use.ĭetach mounting bracket (D) from canopy (E).
Loosen all four preassembled mounting bracket screws (R), then completely remove the two mounting bracket screws (R) from the round holes of canopy (E). Also check the downrod (A) length to ensure the blades (P) will be at least 7 ft. Ensure the blades (P) will be at least 30 in. If using the angle mount, check to ensure the ceiling angle is not steeper than 45°.Ĭlosemount-style mounting is not available for this item.įlushmount installation is not available for this item.ģ.
A longer downrod is sometimes necessary to ensure proper blade clearance. For taller ceilings you may want to use a longer downrod (not included).Īngle-style mounting is best suited for angled or vaulted ceilings. Standard mounting is best suited for ceilings 9 ft. Turn off the circuit breakers and the wall switch to the fan supply line leads. Helpful Tools (not included): AC Tester Light, Tape Measure and Wiring Handbook INITIAL INSTALLATIONġ. Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Step Ladder, Wire Cutters and Wire Strippers If any part is missing or damaged, do not attempt to assemble the product. Compare all parts with the package contents list and hardware contents list.
Harborbreeze fans manual#
Harbor Breeze 41371 Hydra 70-in Brushed Nickel Indoor Residential Ceiling Fan - Use Manual - Use Guide PDF.
0 kommentar(er)
